Active Ethernet I/O with Ethernet and 12 Digital Inputs, 8 Digital Outputs
Especificaciones
- Instant Event Reporting by TCP/UDP/e-mail/SNMP trap
- Easy Local Control without Programming by Patented Click&Go Logic
- 2-point 24VDC digital input with DI/Event counter
- 8 points 24VDC digital output as pulse output
- 10/100Mbps Ethernet with Modbus/TCP protocol Connecting up to 10 hosts
- SNMP to I/O mapping that works with Network Management System
- Windows VB and Windows/WinCE/Linux C API
- Peer-to-Peer I/O without controller
Descripción
Active Ethernet I/O is an exciting new breed of Ethernet I/O that introduces active I/O messaging with easy logic control. Absolutely no programming is required to configure the I/O server’s control logic, due to the patented and intuitive Click&Go™ interface. Bi-directional and direct input-to-output signal communication over Ethernet is supported, and Windows/Linux APIs are included for use in both industrial automation and IT environments. Improve system efficiency via real-time data acquisition
Unlike traditional passive remote I/O, Active Remote I/O provides Active I/O messaging that can send message over Ethernet, TCP/IP network on I/O input status changes or meets certain condition, the message is sent to host computer. Communication between the host computer and Active Remote I/O device is concise and efficient. In addition, the message delivery time is 20 times faster than traditional SCADA systems (50 ms compared to 1 sec).
No programming! Hassle-free Click&Go logic control
Click&Go logic is the key to make ioLogik E2000 series become an intelligent remote I/O. Click&Go logic lets you decide when to send I/O data, and what to say to host computers for simple alarm control and messaging.
As opposed to using C-language or PLC-ladder, a person who understands basic logic concepts can do the configuration themselves, and easily finish their projects. Unlike passive remote I/O architecture, you can integrate Active Remote I/O’s input signals into one event to be an integrated message, and set up local output control at the same time. The unique Click&Go logic is a patent pending technology developed by Moxa.
Unique LCD Display Module for on-site configuration
ioLogik E2000 series Active Remote I/O provides an optional LCD display module for on-site management and configuration. The unique display module can display network and I/O settings, e.g. analog input value, digital input counter value. The IP, netmask address can be set locally without carrying a PC.
Independent Configuration for Multi-functional DI and DO points
Each digital input can be configured independently for DI or Event Counter mode, and each digital output can be independently configured for DO or Pulse Output mode.
Más informaciónes
ioLogik E2210 Specifications
Inputs and Outputs
Digital Inputs
12 channels
Digital Outputs
8 channels
Isolation
3k VDC or 2k Vrms
Digital Input
Sensor Type
Wet Contact (NPN), Dry Contact
I/O Mode
DI or Event Counter
Dry Contact
- On: short to GND
- Off: open
Wet Contact (DI to GND)
- On: 0 to 3 VDC
- Off: 10 to 30 VDC
Common Type
12 points per COM
Counter Frequency
900 Hz
Digital Filtering Time Interval
Software Configurable
Digital Output
Type
Sink
I/O Mode
DO or Pulse Output
Pulse Output Frequency
1 kHz
Over-voltage Protection
45 VDC
Over-current Protection
2.6 A (4 channels @ 650 mA)
Over-temperature Shutdown
175°C (min.)
Current Rating
200 mA per channel
Power Requirements
Power Consumption
203 mA @ 24 VDC
MTBF (mean time between failures)
Time
213,673 hrs
Database
Telcordia (Bellcore)
Common Specifications
LAN
Ethernet
1 10/100 Mbps RJ45 port
Protection
1.5 kV magnetic isolation
Protocols
Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP
Serial Communication
Interface
RS-485-2w: Data+, Data-, GND (3-contact terminal block)
Serial Line Protection
15 kV ESD for all signals
Serial Communication Parameters
Parity
None
Data Bits
8
Stop Bits
1
Flow Control
None
Baudrate
1200 to 115200 bps
Protocol
Modbus/RTU
Power Requirements
Power Input
24 VDC nominal, 12 to 36 VDC
Physical Characteristics
Wiring
I/O cable max. 14 AWG
Dimensions
115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight
under 250 g
Mounting
DIN rail or wall
Environmental Limits
Operating Temperature
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Altitude
Up to 2000 m
Note Please contact us if you require products guaranteed to function properly at higher altitudes.
Standards and Certifications
Safety
UL 508
EMI
EN 61000-3-2; EN 61000-3-3; EN 61000-6-4;
FCC
Part 15, Subpart B, Class A
EMS
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5,
EN 61000-4-6, EN 61000-4-8, EN 61000-4-11, EN 61000-6-2
Shock
IEC 60068-2-27
Freefall
IEC 60068-2-32
Vibration
IEC 60068-2-6
Green Product
RoHS, CRoHS, WEEE
Ordering Information
| Available Modules | |
| ioLogik E2210 | Active Ethernet I/O with 12 digital inputs and 8 digital outputs |
| ioLogik E2210-T | Active Ethernet I/O with 12 digital inputs and 8 digital outputs, -40 to 75°C operating temperature |